Lumber Rollers (to assist in off loading cut boards)
Operations Manual & Parts Book
Bench Grinder (3” wheel w/tooth rest)
Tooth Wrench (for removal and installation of teeth and shanks)
Main Blade Wrench
Lumber Calculator and Cost Calculator
Remote Kill Switch (for gas powered engines)
36 Additional Teeth
BOTH GAS MODELS COME STANDARD AS BOARD & BLOCK PACKAGE: The sawmill is mounted directly on the log at any location, therefore there is no maximum diameter.
Includes: Tools and parts to block up the ends of a log for cutting, 2 wheeled trailer, trailer hitch, Hi-Lift Jack. This method of cutting can be deleted for credit
ALL DIMENSIONS ARE BASED ON THE FACT THAT THE LOG IS NOT BEING TURNED TO ACHIEVE A BOARD CUT SIZE.
IF YOU WANT A SLAB (LARGE BOARD) YOU CAN CUT BOARDS UNTIL YOU REACH YOUR SLAB, THEN FLIP THE LOG AND DO THE SAME TO THE OTHER SIDE UNTIL YOU REACH YOUR EXACT SLAB SIZE.
GAS SAWMILL MODELS
Maximum cut 4 ¼” x 12 ¼” (Using the double edger blades)
Includes: 1700cc (57hp) Engine with electric start, gas tank and 20 feet of Track. The above model and components will allow you to cut any and all sizes of lumber up to 4 ¼” by 12 ¼”.
Maximum cut 8 ¼” x 12 ¼” (Using the large single edger blade)
Includes: All the components and capabilities of the Model 12XLS. In addition add a 19 ½” edger saw blade and all the necessary components to saw any and all sizes of lumber up to 8 ¼” x 12 ¼”,
MODEL 1210 (Mega Mill) ELECTRIC MOTORS ONLY (see Electric Sawmill for details)
Maximum cut 10-1/4” x 12-1/4” (Using the larger single edger blade)
Includes: Two electric motors (25 hp each), 20 feet of heavy duty track 30” Main Blade, 2 – 16-3/4” Edger Blades & 1 – 24-3/4” Edger Blade (large)
ELECTRIC SAWMILL MODELS
ELECTRIC MOTORS STANDARD WITH 12XLS or 128:
1 (15 HP) Electric Motor Driving the Edger Blades
1 (25 HP) Electric Motor Driving the Main Blade
Requires 230 volt or 460 volt 3 phase electric power or 230 volt single phase
(must be used with a phase converter at an additional charge)
ELECTRIC MOTORS STANDARD WITH 1210 2 (25 HP) Electric Motors for Main and Edger Blades
The electric model can only be used with endstand set up or Trailer Package (See pricing for endstand sizes or Trailer )
2 HP AC endstand lift with wiring to panel (only used with the electric sawmill)
Three phase converter: Turns single-phase 230 volt electric power into 230 volt three-phase power.
Can also power other three-phase equipment. (Other voltages may be available)
** NOTE: Electric sawmills have the board & block package deleted from sawmill **
SAWMILL TRAILER SET-UP
The complete sawmill can be towed and operated on a trailer manufactured by Mobile Mfg.
The steel Trailer comes with tandem axle for easy towing and extends (telescopes) to accommodate a maximum of 26’ 4” in sawing length. It comes with 4 foot end stands, 8 foot rack & pinion cross feed, 4 foot track section (to saw 20’ 4” logs), 5 cross beams complete with log holders and log risers. A 48” diameter log is the largest the trailer can hold. The length of 20’ 4” is the standard cutting length.
Adding a 6 foot track section after extending the trailer during set up will allow you to cut logs up to 26’ 4” in length.
Optional Trailer Items:
24 volt powered Log Loading Winch with steel log holding and loading ramps (uses the same batteries as the end stand lift.)
Electric brakes – one axle (may be required in some states)
Spare tire and wheel
Steel log holding and loading ramps(4). Can be used as a loading ramp or a deck for holding logs.
Larger endstands are available for an additional fee (per foot height)
Optional Endstand Items:
Log Holders (Additional ones can be added)
Log Risers (used on tapered logs and to reduce slab size)
Log Holder Slide (used to hold 2 logs at a time)
Motor Lift Options: (Used to raise & lower the sawmill)
¾ hp * 24 volt DC battery endstand lift (requires 2 batteries)
½ hp * 12 volt DC battery endstand lift (requires 1 battery)
¾” hp 115 volt AC electric endstand lift
Optional Steel Frame – (Works with the Endstand set up)
The steel frame made of I-beams and tubing is used to set the endstands up. (Includes 3 log holders)
Price increases for each additional foot of Endstand height
Price increases for each additional foot of Track length
4 foot length
6 foot length
10 foot length
Upgrade from the 1700cc (57hp) which come standard, to the 1835cc (67hp)
Saw Blade Options:
Exchange 6 Tooth 5/16” kerf Main Saw Blade for 12 Tooth ¼” kerf Main Saw Blade
Split Edger Saw Blade – can be added to edger shaft to cut 3 boards at a time
Saw blade Water Coolant system (keeps saw blades cool and clean)
12 volt sealed corrosive battery (gel style able to be shipped)
12 volt battery (cannot be shipped)
Tooth Sharpeners: Saw Mounted Tooth Sharpener (Sharpens saw teeth on the blade)
12 volt battery model (uses connection to engine battery)
115 volt AC model (uses standard electricity, or voltage from the electric mills)
Grindstones for saw mounted tooth grinder (package of 5 grindstones)
Optional extra parts for all saw models:
¼” or 5/16” Stellite inserted saw teeth
Discounted if ordered in quantities of 100 (can mix sizes)
Stellite inserted saw teeth 9/32”
Carbide inserted saw teeth ¼”, 9/32”, 5/16”
Complete set of Belts (Power Bands)
Training: We offer training on the operation and maintenance of the sawmill, Either on the day you pick up your sawmill or any other day that is convenient.
Shipping: You can pick up your sawmill at the factory and go through the training on the same day. We can load most sawmills in a standard pickup truck or you can tow it on the trailer. Sawmills can be shipped anywhere. We charge $600 for crating the sawmill and $600 to crate the large trailer. We will try to find the most competitive rate to your destination.
Terms: A down payment of $1,500 (for gas models) or $2,000 (for electric models) is required with each US, Canadian or Mexican purchase All Overseas (foreign) sales require a $5,000 deposit. If you cancel the order all but $500 is refundable. The balance is due before shipping or picking up your sawmill in the form of a Certified Check, Cashiers Check, or Wire Transfer.